Call Today

 

What are your insights and beliefs on Tools You Need to Install a New Bathtub ?

Mounting a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can relocate easily; if you need to open a wall surface to remove the old tub and also position the new tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. See to it you have actually qualified yourself for the task and fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your washroom if you have currently gotten a brand-new bathtub as well as don't need to transform the plan of your previous water supply pipelines.
Your tools and also material checklist should comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly problematic as a result of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Protect the faucet in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Mounting the Tub

Utilizing both wood boards under its feet, place the bath tub in the needed position. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bath tub up until the level reviews level.
To install faucets, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub needs to wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its final setting.

 

 

Preparing for the Setup

Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall between the bath and the tiling, resulting in issues with dampness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can break rather very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that excerpt was really helpful. Don't hesitate to take a moment to share this entry if you appreciated it. Thank you for your time spent reading it.

Immediate relief? Contact.